planeness
英
美
网络 平面度; 平整度; 平面度,平整度
英英释义
noun
- the property of having two dimensions
双语例句
- A solar panel substrate planeness non contact system is presented, which employs optical triangulation method and bases on virtual precise benchmark.
介绍了一种采用斜光学三角形测量结构和基于虚拟精密测量基准的太阳帆板平面度无接触测量系统。 - Grading Evaluation of Ceramic Tile Planeness Based on Fringe Pattern Phase Analysis
基于条纹相位分析的墙地砖平整度等级评估 - The paper analyses the factors influencing the planeness of asphalt concrete pavement from highway roadbed, spreading material of surface layer, roller compaction and bridge culvert. It also presents the corresponding preventive measures.
从公路路基、路面基层、面层摊铺材料、碾压及桥梁涵洞等方面分析了可能影响沥青砼路面平整度的因素，并提出了相应的预防措施。 - According to the construction experience of many years, the article presents the factors influencing the improvement of asphalt concrete pavement, including subbase planeness, spreading craft, rolling craft, asphalt mixing matter and its thickness and joint.
根据多年的施工经验，提出了基层的平整度、摊铺工艺、碾压工艺、沥青混合料及厚度、接缝等几方面的因素对提高沥青混凝土路面平整度的影响。 - By means of declinate optical triangulation measuring instrument structure which is firstly proposed, the measured area and resolution of this measuring system are greatly increased, and the high accuracy non contact measurement of the planeness of a large area plane is realized.
首次提出斜光学三角形测量结构，使得测量系统的测量面积和分辨率大大提高，从而实现了对大面积平面平面度的高精度无接触测量。 - In this paper, evaluation of uncertainty in measurement of wood-working machine tool planeness was studied by leveling rule with gauge, and the measurement results of planeness was analyzed.
研究了用平尺可调量块测量木工机床平面度的不确定度评定。并对木工机床平面度测量的测量结果进行分析。 - This is needed for planeness error calculation. Motion control was studied. By mechanical and control system design a combined motion control mode was mad.
对测量系统进行了运动控制学研究，采用了位置控制与力控制相结合的组合控制方案，并设计出充分体现这一控制思想的机械结构和控制系统，实现了测量系统的自动行走与测量。 - Because of the particularity of surface structure of solar panel substrate, the classical measuring methods can not satisfy the requirements of planeness measurement.
由于太阳能帆板表面结构的特殊性，传统的测量方法都不能满足其平面度测量的要求。 - During each day's capping operation, check the planeness of the caps prior to compression testing on at least three specimens, selected at random, representing the start, middle, and end of the run.
每天的压顶操作中，在进行抗压试验前，应对至少三个试样上压板的平面度进行检查，这些试样是随机抽取的，分别代表操作开始、中间和结束时所用的试样。 - Based on the actual engineering project of the solar panel substrate planeness measuring system, a detailed analysis of the key technique of the image processing of light spot in the measuring system is presented.
该文在基于实际工程课题的太阳能帆板平面度测量系统基础上，针对测量系统中光斑图像处理这一关键技术进行了详细的研究。