ejecting
英 [iˈdʒektɪŋ]
美 [iˈdʒektɪŋ]
v. 驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词
柯林斯词典
- VERB 驱逐;把…逐出
If youejectsomeonefroma place, you force them to leave.- Officials used guard dogs to eject the protesters...
官员们用警犬驱散抗议人群。 - He was ejected from a restaurant.
他被逐出餐厅。
- Officials used guard dogs to eject the protesters...
- VERB 弹出;喷出;射出
Toejectsomething means to remove it or push it out forcefully.- He aimed his rifle, fired a single shot, then ejected the spent cartridge.
他用步枪瞄准,射出一枚子弹,然后退出空弹壳。
- He aimed his rifle, fired a single shot, then ejected the spent cartridge.
- VERB (通常指飞行员从即将坠毁的飞机中)弹射出来
When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.- The pilot ejected from the plane and escaped injury.
飞行员从飞机中弹出,安然无恙。
- The pilot ejected from the plane and escaped injury.
双语例句
- Design injection mould with quadratic ejecting mechanism of slider and wedge dual push plate
推床的导板(或推板)滑块斜楔双推板式二次推出机构注塑模的设计 - So, for example, it's not just the2 p that we could actually take an electron from, we could also think about ejecting an electron from the2 s orbital.
比如,我们不只可以从,2,p,轨道上,打出一个电子,还能考虑从,2,s,轨道上,发射出一个电子。 - Througn designing three axial slots in internal threaded portion and optimizing nib structure, a design was made on the injection mould with a two-step ejecting mechanism with non-rotating.
对笔尖内螺纹部分设计三段轴向开槽,优化笔尖结构,设计了二次推出不带旋转机构的自动脱螺纹注塑模。 - Some critics believe that World Cup games ought to use referees with experience ejecting superstars like Cristiano Ronaldo. '
一些批评者认为,世界杯比赛使用的裁判一定要有把像C・罗纳尔多(CristianoRonaldo)那样的超级球星罚下场的经验。 - The mixing performance of cross flow was studied in turbine ejecting mixer with tracing technique.
采用示踪法研究了涡轮喷射混合器内错流射流混合特征。 - Finally, the location and size of the ejector pins that correspond to the discrete ejecting forces are obtained.
最后,这个位置和大小的异形销,迎合了离散排出力量。 - During an attempt at ejecting the CD magazine.
在试图弹出CD盒期间。 - The design of side core-pulling framework and ejecting framework is difficult in designing injection mould.
侧面抽芯机构和顶件机构的设计是注射模具设计的难点。 - The experiment shows that it can drag reduction and extend the discharge distance of pipeline transportation by ejecting compressed air to dredger pipeline.
分析了管道输送加气减阻的机理和延长排距的效果,在模型试验的基础上进行了实船试验。 - Each front bracket convex plate is provided with at least two guiding slopes which are in different radians and can be butted with the pushed part of the ejecting unit.
每个前托凸板都具有至少两个弧度不同并可靠抵在通出单元的受推部上的导引斜面。